BACK TO PRODUCTS

Primer

Core Range

Filter by

Products

101 Product Found
My Filters
    Primer
    Interbuild 1002
    Interbuild 1002 is a high performance, two component epoxy primer with excellent chemical and abrasion resistance. It exhibits good penetration properties to ensure good adhesion on concrete floors. Interbuild 1002 is especially suited for properly prepared concrete substrates.
    Primer
    Devran 261
    A high performance, chemically cured, epoxy primer/intermediate for steel
    Primer
    Intergard 361
    A two pack, low temperature cure, epoxy universal primer which can be overcoated with various finish coats such as polyurethane, epoxy and alkyd finishes after extended periods, without the use of a tie coat. It is also used as a primer over galvanised steel and stainless steel.
    Primer
    Intershield 300V
    A light coloured, abrasion resistant, aluminium pure epoxy coating giving excellent long term anticorrosive protection and low temperature application capability.
    Primer
    Intergard 7500
    A two component, high volume solids, abrasion resistant pure epoxy coating pigmented with aluminium that provides excellent long term anti-corrosive protection. Intergard 7500 is capable of fast cure and has low temperature cure properties. Ideally suited for use as a universal primer in protecting underwater areas, splashzones, decks and structural steel.
    Primer
    Interprime 4198
    A one component, fast drying, high performance, universal alkyd primer pigmented with zinc phosphate. Suitable for use as a primer with single pack polysiloxanes.
    Primer
    Devprime 1403
    A heavy duty, high quality, rust inhibitive alkyd primer for use over properly prepared steel. A high performance shop primer with high volume solids providing increased coverage rates and one coat application. *Please note this product is only available in North America.
    Preconstruction Primer
    Interplate 997
    A two pack, heat resistant zinc silicate shop (pre-construction) primer providing good corrosion protection (even after heating up to 800°C (1472°F)), with minimum production of zinc salts. Suitable for high speed welding and cutting with excellent resistance to damage caused by welding, gas cutting and fairing thereby reducing secondary surface preparation requirements in comparison to typical zinc silicate products.
    Primer
    Interprime 1068
    Interprime 1068 is an air drying Zinc Phosphate Primer designed for application to all types of steel surfaces. This primer is characterised by good anti-corrosive properties, easy application and the ability to protect hand cleaned steel. Interprime 1068 is primarily intended as a single coat system for use in mildly corrosive environments, classified in ISO12944-2 as up to and including C2.
    Primer
    Interprime 234
    A one component, high build alkyd primer containing anticorrosive pigment.
    Primer
    Devprime 1401
    A rust inhibitive primer for use over properly prepared steel. A general purpose shop primer, Devprime 1401 offers low cost, easy application and low VOC. *Please note this product is only available in North America.
    Temporary Protection
    RELEST Wind ProcessCoat - I373-2050
    RELEST Wind ProcessCoat is a Solvent-free translucent 2K polyurethane for use as an in-mold gelcoat with low film thicknesses. Utilizing the new generation of UV absorbers allows for temporary outdoor storage of uncoated rotor blades, without the risk of UV light damaging the substrate. The product's great sandability facilitates the further treatment of demoulded rotor blades and forms an excellent, pore-free basis for subsequent coatings.
    Primer
    Devprime 1409
    A high solids, rust-inhibitive, interior-exterior alkyd primer for use on ferrous and non-ferrous metal including galvanized metal and aluminium. *Please note this product is only available in North America.
    Primer-Finish
    RELEST Wind Adhesion Promoter - I367-0080
    RELEST Wind Adhesion Promoter is a two component polyurethane material designed to ensure optimal adhesion for PVC, aluminium cast, CDC, PMAA and GRP based on epoxy or polyester. It is is especially suited for use in combination with wear protection coatings for rotor blades.
    Preconstruction Primer
    Interplate 937
    A two pack, heat resistant zinc silicate shop (pre-construction) primer providing good corrosion protection (even after heating up to 800°C (1472°F)), with minimum production of zinc salts. Suitable for high speed welding and cutting with excellent resistance to damage caused by welding, gas cutting and fairing thereby reducing secondary surface preparation requirements in comparison to typical zinc silicate products.
    1. 1

    Sorry, we couldn't find any results
    Fetching the data, please wait...