Intercrete = International + Flexcrete
A two component, thixotropic, polymer modified cementitious coating for the protection of concrete substrates. *Selective Countries Only - Please contact your local representative.
Intercrete 4890 is a single pack, low VOC, water-based, modified styrene acrylic copolymer decorative concrete coating that provides excellent protection against carbonation and water ingress without entrapping moisture within damp substrates. Elastomeric properties enable the system to accommodate hairline cracks and substrate movement while providing lasting protection. Adhesion is excellent to mineral substrates.
Specifically designed for the non-structural repair and reinstatement of concrete, brick or stone substrates. Intercrete 4803 is a low density, lightweight, fibre reinforced, polymer modified shrinkage compensated mortar that exhibits high bond strength exceeding the tensile strength of concrete, ensuring monolithic performance of the repair. Can be applied up to 100mm in a single layer in vertical, horizontal and overhead situations. CE-marked in accordance with EN 1504-3 Class R2. Suitable for repair methods 3.1, 7.1, 7.2 as defined by BS EN 1504-3.
Specifically designed for the structural repair and profiling of vertical, horizontal and overhead surfaces in marine and tidal areas which are subject to early immersion. Intercrete 4804 is a thixotropic mortar which allows easy trowel application whilst enabling high application thicknesses up to 50mm per layer in both vertical and horizontal applications. Excellent resistance to wash-out soon after application. CE-marked in accordance with BS EN 1504-3 Class R4. Suitable for repair methods 3.1, 3.2, 7.1, 7.2 as defined by BS EN 1504-3.
Specifically designed for the structural repair of large areas of concrete and heavy duty applications beneath base plates, plinths and stanchion bases where a pourable or flowable material is required. Intercrete 4805 utilises a dual expansion mechanism which compensates for shrinkage in the plastic and hardened state and cures rapidly to give high early and long term strength development, enabling quick reinstatement. The dense matrix provides excellent protection from the ingress of acid gases, moisture and chlorides.
Specifically designed for the filling of tieholes formed by formwork bolts in new construction, particularly where a rapid setting, durable, waterproof mortar is required. Can also be used for sealing grout holes and voids around fixings in pre-cast elements. Intercrete 4807 sets in 30 minutes at 20°C, yielding a durable, high strength mortar which provides a waterproof seal which withstands 10 bar water pressure after only 72 hours curing. Non-toxic when cured and WRAS approved for use incontact with potable water. CE-marked in accordance with BS EN 1504-3 Class R4. Suitable for repair methods 3.1, 7.1, 7.2 as defined by BS EN 1504-3.
Specifically designed for the structural repair of large areas of concrete and heavy duty applications beneath base plates, plinths and stanchion bases where a pourable or flowable material is required. Intercrete 4806 utilises a dual expansion mechanism which compensates for shrinkage in the plastic and hardened state and cures rapidly to give high early and long term strength development, enabling quick reinstatement. The dense matrix provides excellent protection from the ingress of acid gases, moisture and chlorides.
Specifically designed for arresting water seepage and infiltration under pressure through cracks, joints, and voids in concrete and masonry. Intercrete 4809 sets in 2 minutes at 20ºC, yielding a durable, high strength mortar which provides rapid sealing and jointing in and around pipework or for forming fillets in tanking situations.
Designed to enhance the bond between high porosity concrete and Flexcrete Repair Mortars. Intercrete 4812 further increases the adhesion of Flexcrete Repair Mortars and prevents rapid drying at the concrete interface on porous backgrounds with high suction.
Ultimately designed to prime substrates and promote adhesion prior to the application of one of both decorative and protective membranes. Intercrete 4813 is a single component product and is compatible with a wide range of ferrous, non-ferrous metals and difficult to adhere to substrates including steel, lead, zinc, aluminium, copper, flashband, bitumen paint and roofing felt. It is ideally suited for use in combination with the Intercrete range of cold applied liquid roofing system for the anti-corrosion protection of roofs with metallic protrusions.