Lining
Enviroline 376F-30LT
Low Temperature Application and Cure Tank Lining.
BACK TO PRODUCTS
Thermal Power
Product Applications
We offer a wide range of high performance coatings that provide long term corrosion protection and aesthetics
Filter by
Products
My Filters
Other
RELEST Wind Leading Edge Cartridge
RELEST Wind LEP Cartridge is a two-component solvent-free polyurethane coating which is especially designed for protecting the leading edge of rotor blades of wind energy plants from erosion damage caused by rain, sand, hail, dirt and other particles suspended in the air. The coating consists of an exceptionally fast, hard wearing, UV- and abrasion resistant polyurethane elastomer. It is supplied in a convenient 2-component cartridge for direct application of minimal quantities without weighing.
Primer-Finish
Interbuild 1073
Interbuild 1073 is a two component, high solids content epoxy primer typically used in maintenance environments due to excellent surface tolerance properties. With a low VOC content, the primer can also be applied within internal environments and complies with the Indoor air quality standard as stipulated by EPA Method 24.
Primer
Interprime 1068
Interprime 1068 is an air drying Zinc Phosphate Primer designed for application to all types of steel surfaces. This primer is characterised by good anti-corrosive properties, easy application and the ability to protect hand cleaned steel. Interprime 1068 is primarily intended as a single coat system for use in mildly corrosive environments, classified in ISO12944-2 as up to and including C2.
Finish
Intercryl 530 (Formerly Devcryl 1448)
A premium quality, low VOC, direct to metal acrylic semi-gloss enamel for high traffic interior - exterior areas of commercial, institutional and industrial structures. *Please note this product is only available in North America.
Filler
RELEST Wind Putty Contour Cartridge - I373-3715
RELEST Wind Putty Contour Cartridge is a Solvent-free, highly viscous polyurethane putty for smoothing surface and contour irregularities. Its easy sanding and rapid cure properties offers increased productivity for further processing and recoating. RELEST Wind Putty Contour is ideally situated for mechanical application. It is supplied in a convenient 2-component cartridge for direct application of minimal quantities without weighing.
Intermediate
RELEST Wind Gelcoat Transparent - I372-0002
RELEST Wind Gelcoat Transparent is a viscoplastic, solvent-free polyaspartic coating with high tear propagation strength for use as an in-mould gelcoat. Suitable for making transparent, bubble-free and fast drying intermediate coats. RELEST Wind Gelcoat Transparent offers a pore-free surface after demoulding with very good UV stability allowing it to be topcoated without any additional working steps.
Finish
Devthane 379N
A low VOC, two component modified acrylic polyurethane finish giving excellent durability and long-term
recoatability, for use over correctly prepared primed surfaces. This product is also HAPS free and
exempt solvent free.
recoatability, for use over correctly prepared primed surfaces. This product is also HAPS free and
exempt solvent free.
Primer-Finish
Intergard 452
Intergard 452 is a two component, high build epoxy intermediate. Pigmented with micaceous iron oxide to comply with the requirements of BS5493:1977
Other
Interplus 4102 Odin Gel
A single component, water-based rust remover / cleaner gel. Interplus 4102 Odin Gel is 100% biologically degradable, free for toxins and conforms to the yellow classification of the Harmonised Offshore Chemical Notification Format (HOCNF).
Other
High Temperature 904
Designed to protect and decorate metal surfaces, such as the exterior of ovens, boilers, chimneys, pipes, machinery, and equipment exposed to temperatures not exceeding 290°C (408.2°F) in dry conditions, in covered environments.
Other
Machinery Enamel 11271
Provides protection and decoration for metal surfaces in low aggressiveness environments (interior or exterior).
Other
High Temperature 901
Perfect for protecting and decorating the exterior of metal surfaces such as ovens, boilers, chimneys, pipes, and machinery in indoor environments (under cover). It can also be used on cement, concrete, or fiber-cement substrates exposed to dry temperatures of up to 260°C (500°F). It is recommended for indoor environments with medium aggressiveness. Not recommended for immersion.
Other
Epoxy Coal Tar Free
Designed for exterior protection in environments with exposure to fumes, dust, solvent splashes, and spills. It is used as an exterior coating for tanks in coastal areas and marine environments, as well as for buried pipes and continuous immersion in fresh and saltwater and some specifically recommended chemical solutions. For outdoor exposure, it is recommended to use a corrosion-inhibiting primer for optimal results.
Two coats are required for immersion service.
*For more information, consult International Technical Support.
Two coats are required for immersion service.
*For more information, consult International Technical Support.