Filter by

Buildings

Mining

Commercial Buildings

Mining Processing Equipment

Rail

Shiploading, Jetties and Wharfs

Waste Distribution

Offshore Oil and Gas facilities

Onshore Oil and Gas facilities

Thermal Power

Transportation and Pipeline

Water and Waste

Wind Power

Blades

Coal Power

Commercial Buildings

Foundations

Pipeline

Rail

Substations

Turbines and Towers

Waste Distribution

Products

278 Product Found

My Filters

Lining

Interline 961

A two component, solvent based epoxy phenolic tank lining for application to both new steel, or lightly pitted surfaces.

Primer

Pre-Prime 167

A high performance, two-component chemically-cured 100% solids epoxy penetrating sealer.

Primer

Interdur 8805

A two component, rapid recoat, fast curing solvent based inorganic zinc rich ethyl silicate primer. Conforms to SSPC Paint 20 Level 3. Available in ASTM D520, Type II zinc dust version as standard.

Finish

Devthane 379

A high performance, two-component chemically-cured aliphatic urethane gloss finish. *Please note this product is only available in North America.

Structural Concrete- Repair and Protection

Intercrete 4804 (formerly Marine Mortar S)

A two component, water-based (VOC-free), fibre reinforced, polymer modified, cementitious mortar with excellent adhesion for use in areas subject to early immersion. Intercrete 4804 cures rapidly to produce a high strength mortar with enhanced polymeric properties for the repair of voids in aggressive marine environments. Suitable for thicknesses up to 50mm.

Reference

Ceilcote 610 Ceilpatch

Ceilcote 610 Ceilpatch is a chemical-resistant epoxy patching/filling compound that is used to fill defects in concrete or steel surfaces prior to the application of Ceilcote lining, coating or flooring systems. It provides excellent adhesion to concrete or steel, minimal shrinkage and superior chemical resistance.

Temperature Resistance

Intertherm 50

A single component, high temperature coating based on a moisture-curing silicone binder, Intertherm 50 is ideal for the protection of steel from corrosion at temperatures up to 540°C (1004°F). The moisture-curing crosslinking technology of Intertherm 50 allows multiple coats to be applied without heat curing.

Intermediate

Intergard 475HS

Intergard 475HS is a low VOC, high solids, high build epoxy used to improve barrier protection for a range of anticorrosive coating systems in a wide range of aggressive environments. Intergard 475HS can be pigmented with MIO to provide improved overcoating properties, better facilitating application in the fabrication shop.

Primer

Interzinc 2277

Part of the Interzinc 22 series of products.A two component, rapid recoat, fast curing solvent based inorganic zinc rich ethyl silicate primer. Conforms to SSPC Paint 20 Level 2Available in ASTM D520, Type II zinc dust version as standard.

Lining

Interline 955

A two component, heavy duty vinyl ester coating reinforced with glass flake to increase chemical and abrasion resistance.A chemically resistant, vinyl ester coating which can be applied using standard airless spray equipment at material temperatures up to 35°C (95°F).

Finish

Devgrip 238

Devgrip 238 is a two component, abrasion resistant epoxy coating. *Please note this product is only available in North America.

Temperature Resistance

Intertherm 228HS

A highly crosslinked, two component, high build epoxy phenolic coating, Intertherm 228HS combines properties of corrosion and chemical resistance when used in high temperature service. Based upon novolac resin technology, Intertherm 228HS can be used in a wide range of highly corrosive environments operating at temperatures up to 230°C (446°F).

Other

Enviroline 405HTR MR System

Enviroline 405HTR MR is a reinforced chemcial resistant system. The system features a high temperature reesistant, 100% volume high solids, two component polycyclamine cured lining topcoat. Fibre glass mat reinforcement increases physical properties and where necessary allows dynamic crack bridging in concrete.In the table below you can find System Sheet and Application guidelines. For Technical Datasheets and MSDSs please click on the links to the individual component products of the system below the table.

Chemical Resistant Lining

Ceilcote 800 Coroline

CEILCOTE 800 Coroline lining is a heavy duty, monolithic flooring/lining system that is designed to protect concrete and metal against attack by corrosive chemicals and mechanical abuse. Based on novolac epoxy technology, CEILCOTE 800 Coroline lining provides exceptional resistance to 98% Sulfuric Acid, Sodium Hydroxide and other aggressive chemicals.

Primer-Finish

Intercure 3240G

A two component, gloss, low VOC, high solids, fast drying polyaspartic primer/finish coating. Intercure 3240G provides improved productivity at ambient temperature application whilst combining the anti-corrosive performance of epoxy coatings and high aesthetics of UV durable topcoats in a single coat application. Intercure 3240G is applied as a single coat direct to correctly prepared substrates using manual mix (single leg) or automatic mix (plural leg) application equipment, reducing application time, energy consumption and labour costs when compared to two coat applications, or single coat applications which require force drying at high temperature.

Thermal Power

CASES

Optimized Capacity with Interline 984

Filter by

Products

Propelled by curiosity

International products are developed and produced by AkzoNobel