Lining
Interline 961
A two component, solvent based epoxy phenolic tank lining for application to both new steel, or lightly pitted surfaces.
BACK TO PRODUCTS
Onshore Oil and Gas
Reliable Coating Solutions for Long-Lasting Performance
- Extend service life with durable coatings.
- Reduce unplanned shutdowns with corrosion protection.
- Optimize efficiency in tough onshore environments.
Filter by
Products
My Filters
Grout
Ceilcote 748 Corrosion Grout
CEILCOTE 748 Corrosion Grout is a three-component chemicalresistant epoxy grouting material. It provides high strength, good adhesion to concrete and steel, minimal shrinkage and resists degradation by corrosive chemicals.
Primer
Pre-Prime 167
A high performance, two-component chemically-cured 100% solids epoxy penetrating sealer.
Primer
Interdur 8805
A two component, rapid recoat, fast curing solvent based inorganic zinc rich ethyl silicate primer. Conforms to SSPC Paint 20 Level 3. Available in ASTM D520, Type II zinc dust version as standard.
Finish
Devthane 379
A high performance, two-component chemically-cured aliphatic urethane gloss finish. *Please note this product is only available in North America.
Structural Concrete- Repair and Protection
Intercrete 4804 (formerly Marine Mortar S)
A two component, water-based (VOC-free), fibre reinforced, polymer modified, cementitious mortar with excellent adhesion for use in areas subject to early immersion. Intercrete 4804 cures rapidly to produce a high strength mortar with enhanced polymeric properties for the repair of voids in aggressive marine environments. Suitable for thicknesses up to 50mm.
Primer
Intergard 436
A two component clear epoxy sealer.Can be applied to slightly damp concrete. Cures quickly, long pot life. Excellent resistance to most alkalis, solvents, mild acids and water. Good toughness and resilience. Excellent binding properties to weathered fibrous cement sheeting.
Temperature Resistance
Intertherm 50
A single component, high temperature coating based on a moisture-curing silicone binder, Intertherm 50 is ideal for the protection of steel from corrosion at temperatures up to 540°C (1004°F). The moisture-curing crosslinking technology of Intertherm 50 allows multiple coats to be applied without heat curing.
Intermediate
Intergard 475HS
Intergard 475HS is a low VOC, high solids, high build epoxy used to improve barrier protection for a range of anticorrosive coating systems in a wide range of aggressive environments. Intergard 475HS can be pigmented with MIO to provide improved overcoating properties, better facilitating application in the fabrication shop.
Subsea, Abrasion Resistant and Splashzone
Interzone 762
A two component, styrene free, glass flake reinforced ambient cure polyester/acrylic copolymer coating.
Primer
Interzinc 2277
Part of the Interzinc 22 series of products.A two component, rapid recoat, fast curing solvent based inorganic zinc rich ethyl silicate primer. Conforms to SSPC Paint 20 Level 2Available in ASTM D520, Type II zinc dust version as standard.
Lining
Interline 955
A two component, heavy duty vinyl ester coating reinforced with glass flake to increase chemical and abrasion resistance.A chemically resistant, vinyl ester coating which can be applied using standard airless spray equipment at material temperatures up to 35°C (95°F).
Structural Concrete- Repair and Protection
Intercrete 4893 (formerly Monodex Clear)
A single component, low VOC, transparent coating that offers an excellent defence against carbon dioxide ingress and the effects of weathering, significantly prolonging the maintenance free life of buildings and structures. Applied without a primer, it forms a clear, satin finish that retains the original appearance of the concrete substrate to which it is applied. It prevents water ingress, yet allows damp substrates to breathe and dry out, and is both dirt and UV resistant. Long term protection from the growth of mould and fungi is assured with the use of advanced encapsulated biocide technology to help maintain its original appearance.