Lining
Interline 961
A two component, solvent based epoxy phenolic tank lining for application to both new steel, or lightly pitted surfaces.
BACK TO PRODUCTS
Wind Power
Comprehensive Coating Solutions for Renewable Energy
- Protect wind turbines from harsh environments.
- Extend component lifespan from tip to toe.
- Ensure compliance with industry standards.
Filter by
Products
My Filters
Primer
Interdur 8805
A two component, rapid recoat, fast curing solvent based inorganic zinc rich ethyl silicate primer.
Conforms to SSPC Paint 20 Level 3.
Available in ASTM D520, Type II zinc dust version as standard.
Conforms to SSPC Paint 20 Level 3.
Available in ASTM D520, Type II zinc dust version as standard.
Finish
Devthane 379
A high performance, two-component chemically-cured aliphatic urethane gloss finish.
Primer
Interdur 8815
A two component, metallic zinc rich epoxy primer which complies with the composition and
performance requirements of HG/T3668.
performance requirements of HG/T3668.
Structural Concrete- Repair and Protection
Intercrete 4804 (formerly Marine Mortar S)
A two component, water-based (VOC-free), fibre reinforced, polymer modified, cementitious mortar with excellent adhesion for use in areas subject to early immersion. Intercrete 4804 cures rapidly to produce a high strength mortar with enhanced polymeric properties for the repair of voids in aggressive marine environments. Suitable for thicknesses up to 50mm.
Temperature Resistance
Intertherm 50
A single component, high temperature coating based on a moisture-curing silicone binder, Intertherm 50 is ideal for the protection of steel from corrosion at temperatures up to 540°C (1004°F). The moisture-curing crosslinking technology of Intertherm 50 allows multiple coats to be applied without heat curing.
Intermediate
Intergard 475HS
Intergard 475HS is a low VOC, high solids, high build epoxy used to improve barrier protection for a range of anticorrosive coating systems in a wide range of aggressive environments. Intergard 475HS can be pigmented with MIO to provide improved overcoating properties, better facilitating application in the fabrication shop.
Lining
Interline 955
A two component, heavy duty vinyl ester coating reinforced with glass flake to increase chemical and abrasion resistance.A chemically resistant, vinyl ester coating which can be applied using standard airless spray equipment at material temperatures up to 35°C (95°F).
Surface Pre-Treatment
Interplus 614
A single component, water based rust remover gel, which can be described as readily biodegradable as tested by OECD 301B CO2 Evolution test.
Temperature Resistance
Intertherm 228HS
A highly crosslinked, two component, high build epoxy phenolic coating, Intertherm 228HS combines properties of corrosion and chemical resistance when used in high temperature service. Based upon novolac resin technology, Intertherm 228HS can be used in a wide range of highly corrosive environments operating at temperatures up to 230°C (446°F).
Structural Concrete- Repair and Protection
Intercrete 4874 (formerly Cemprotec 2000-BJT)
A high performance butyl tape which is designed to join two pieces of Intercrete 4872 waterproof composite tape together. Embedded into our Intercrete range of cementitious coatings, it forms an elastomeric joint between two lengths of tape to accommodate movement.
Structural Concrete- Repair and Protection
Intercrete 4811 (formerly Bond-Prime)
A single component, water-based (VOC free), rapid curing, acrylic copolymer modified with a unique water-emulsified epoxy cross-linking agent. Intercrete 4811 is inherently hydrophobic and alkali resistant, making it ideal for application to a wide range of new and aged mineral substrates.
It is non-hazardous, and application is by brush, roller or airless spray to prime and stabilise surfaces prior to the application of Flexcrete’s specialist membranes. Intercrete 4811 cures to form a clear film with an identifying green tint, both on and within the substrate, to provide an ideal surface for subsequent treatment.
It is non-hazardous, and application is by brush, roller or airless spray to prime and stabilise surfaces prior to the application of Flexcrete’s specialist membranes. Intercrete 4811 cures to form a clear film with an identifying green tint, both on and within the substrate, to provide an ideal surface for subsequent treatment.
Passive Fire Protection
Interchar 3120
Interchar 3120 provides thin and thick film capabilities, easy to apply and durable epoxy intumescent coating that provides cellulosic passive fire protection (PFP) for off site applied structural steel. It increases production efficiency, reduces site work and coating schedules.