We are a single source supplier of coatings for wind turbines - from tip to toe.
Specifically designed for rapid cosmetic repairs to in-situ and pre-cast concrete where repairs need to be colour matched to the parent concrete to provide a highly aesthetic finish. Intercrete 4808 demonstrates rapid strength development, achieving over 9MPa in 2 hours. Ultimate physical properties of cured materials are similar to base concrete.Not suitable for repairs deeper than 25mm. CE-marked in accordance with BS EN 1504-3 Class R1. Suitable for repair methods 3.1 as defined by BS EN 1504-3.
Specifically designed be embedded in the INTERCRETE range of cementitious coatings to provide a highly flexible impermeable seal over ‘live’ cracks and expansion or construction joints in waterproofing applications.
Intercrete 4872 is a permanently elastomeric composite tape exhibiting over 600% elongation which enables rapid application of the INTERCRETE range.
Provides excellent weathering resistance and is highly tolerant of a wide range of chemicals and is impermeable to water under 10 bar hydrostatic pressure (100m head of water).
Designed to remove light to medium rust deposits from a variety of surfaces. Suitable as a cleaning agent to remove rust stains in coated areas. Can be used as an alternative to traditional sandblasting, ultra-high pressure water blasting or power tool methods where these have been ruled out for operational, health and safety or environmental reasons. Effective for removal of corrosion on stainless steel structures and aluminium.
Specifically designed for the general purpose structural repair and reinstatement of concrete in single coat applications up to 80mm in a single layer.
Intercrete 4800 offers low permeability to water at 10 bar positive and negative pressure along with excellent resistance to carbon dioxide gas and chloride ion diffusion.
CE-marked in accordance with BS EN 1504-3, Class R3. Suitable for repair methods 3.1, 3.3, 7.1, 7.2 as
defined in BS EN 1504-3.
For polymer modification of sand and cement mortars to provide enhanced mechanical characteristics:
When mixed with cement, can be used as a primer and a bonding agent for polymer mortars, renders and screeds.
Can also be diluted with water to produce a primer for roof and deck applications in the clean water industry. WRAS Approved for use in contact with potable water.
Designed to be used to treat a range of substrates, including: Concrete Mortars and Renders, Masonry, Polyurethane Foam, Phenolic Board Existing Paints
Plaster and Intercrete Concrete Repair Mortars. Intercrete 4811 enhances bond by combining penetration into the pore structure with a surface film-forming effect to produce a stabilised, sound surface ideal for treatment.
Reacts with subsequently applied coatings to provide a chemical bond giving excellent adhesion and dries quickly without the release of hazardous solvents and can be overcoated after just 1 hour.
Specifically designed to be broadcast into the surface of INTERCRETE coatings to aid curing and provide a durable slip and abrasion resistant finish.
INTERCRETE 4854 grit provides a hard-wearing, slip-resistant surface which will provide ultimate protection against foot traffic, wheelchair use, impact from heavy objects and attack from the elements.
Supplied as a 100mm wide preformed strip on siliconised release paper, the backing strip is simply removed upon application. Non-toxic and approved for use in contact with potable water, Intercrete 4874 is ideal for use in a wide range of waterproofing applications, such as reservoirs, water tanks, roof slab and projects in enclosed locations where it is not suitable to use solvent-based or hot welded products
Supplied in two grades for the reinforcement of the Flexcrete range of cementitious mortars and coatings:
INTERCRETE SCRIM: Particularly suited for general reinforcement over large areas of cracking/crazing or weak/friable substrates, particularly insulation, to provide increased tensile strength and impact resistance.
INTERCRETE EDGE SCRIM: For localised reinforcement over joints or cracks to provide increased tensile strength. Can also be used over welds or edges of steel sections to help maintain correct film thickness. Self-adhesive.
Corrosion & fire protection coatings for buildings
Coatings for abrasive and corrosive environments
Coatings & fire protection for upstream oil & gas
Coatings & fire protection for downstream oil & gas