Preconstruction Primer
Interplate 408
A two component iron oxide epoxy shop primer. Approved for welding by Newcastle Primary Care Trust (NOHA). Approved for welding by Lloyd's Register.
BACK TO PRODUCTS
Wind Power
Comprehensive Coating Solutions for Renewable Energy
- Protect wind turbines from harsh environments.
- Extend component lifespan from tip to toe.
- Ensure compliance with industry standards.
Filter by
Products
My Filters
Primer
Intergard 276
A quick drying two component epoxy primer.Suitable for overcoating after prolonged periods of weathering.
Other
Interdur 1130
Interdur 1130 is an easy to use primer and finish in one. The product is well suited to a variety of uses including: internal steelwork where a good appearance is desired, external steelwork in low and moderate corrosion environments, OEM such as pre-engineered buildings (PEB). As a single component product, Interdur 1130 is a simple solution for the maintenance of existing structures.
Other
RELEST Wind Gelcoat - I372-7338
RELEST Wind Gelcoat ca. RAL 7038, RA is a solvent free 2k viscoplastic, polyaspartic coating with excellent abrasion resistance. Suitable as part of a coating system for UV- and weather- resistance. Film thicknesses of approximately 200μm can be achieved in one step with optimal flow properties. RELEST Wind Gelcoat ca. RAL 7038, RA is characterised by its great adhesion to epoxy laminate.
Filler
RELEST Wind Putty Contour Cartridge - I373-3715
RELEST Wind Putty Contour Cartridge is a Solvent-free, highly viscous polyurethane putty for smoothing surface and contour irregularities. Its easy sanding and rapid cure properties offers increased productivity for further processing and recoating. RELEST Wind Putty Contour is ideally situated for mechanical application. It is supplied in a convenient 2-component cartridge for direct application of minimal quantities without weighing.
Other
RELEST Wind LEP ETU - I374-8735
RELEST Wind LEP Easy To Use is a two-component solvent-free polyurethane coating for the M&R market which is especially designed for protecting the leading edge of rotor blades of wind energy plants from erosion damage caused by rain, sand, hail, dirt and other particles suspended in the air. The coating consists of an exceptionally fast, hard wearing, UV- and abrasion resistant polyurethane elastomer.
Surface Pre-Treatment
Devprep 88
A concentrated water based cleaner low in odour, non-flammable and biodegradable.
Primer-Finish
RELEST Wind Adhesion Promoter - I367-0080
RELEST Wind Adhesion Promoter is a two component polyurethane material designed to ensure optimal adhesion for PVC, aluminium cast, CDC, PMAA and GRP based on epoxy or polyester. It is is especially suited for use in combination with wear protection coatings for rotor blades.
Temporary Protection
Interseal 121
A single component, spray applied, high build, water based coating for direct application over coated substrates and non-ferrous substrates. Interseal 121 dries to form a non-tacky, tough, resilient temporary protective layer.Interseal 121 utilises patented peelable technology to ensure rapid and complete removal at a wide range of temperatures without deterioration to the underlying coating or substrate.
Intermediate
RELEST Wind Gelcoat Transparent - I372-0002
RELEST Wind Gelcoat Transparent is a viscoplastic, solvent-free polyaspartic coating with high tear propagation strength for use as an in-mould gelcoat. Suitable for making transparent, bubble-free and fast drying intermediate coats. RELEST Wind Gelcoat Transparent offers a pore-free surface after demoulding with very good UV stability allowing it to be topcoated without any additional working steps.
Finish
Devthane 378
A high performance, two component, chemically cured, aliphatic urethane semi-gloss finish.
Primer
Ceilcote 380
Ceilcote 380 is a catalysed vinyl ester primer for concrete and steel substrates. It provides excellent bonding and adhesion for various polyester or vinyl ester linings, coating and flooring systems as well as Ceilcote Hybrid Polymer systems. The addition of Ceilcote C#1 powder provides conductivity where required.